Short Articles

ASTM A – Designation: A /A M – 02a Standard Speci?cation for Steel Sheet, Aluminum-. Find the most up-to-date version of ASTM A at Engineering ASTM A/AM: Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process.

Author: Tur Kigarisar
Country: Djibouti
Language: English (Spanish)
Genre: Health and Food
Published (Last): 19 July 2005
Pages: 369
PDF File Size: 2.58 Mb
ePub File Size: 3.59 Mb
ISBN: 735-5-52516-412-8
Downloads: 68777
Price: Free* [*Free Regsitration Required]
Uploader: Mejas

Link to Active This link will always route to the current Active version of the standard. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

We appreciate your input. A number in parentheses indicates the year of last reapproval. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Please read our License Agreement regarding astn data and our Privacy Policy.

A superscript epsilon e indicates an editorial change since the last revision or reapproval. These notes and footnotes excluding those in tables and figures shall not be considered as requirements of the standard.

B Weight [mass] to thickness conversions are reliable to only two signi?

Those who use these documents must determine which speci? The typical mechanical properties included in the new designation system are those indicated by the tension test. This is not considered to be a asym of the steel but is rather a function of the induced cold-work. D If a higher tensile strength is required, the user should consult the producer.

The new designations are de? Dimensions and Permissible Variations 9. A greater number of digits are shown in Table X2. Aluminum-coated type 1 steel, coils or cut sheet Coated with aluminum-silicon alloy by hot dip process Used for combustion chambers, exhaust systems, heat exchangers and reflectors, ovens, grills, and appliances. They are solely to provide the purchaser with as much information a643 possible to make an informed decision on the a4633 to be speci?


It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Please contact us at webmaster matweb. These properties are more predictive of steel formability than other tests, such as the hardness test, which may not compensate adequately for product variables such as substrate thickness and coating weight.

We also ask that you refer to MatWeb’s terms of use regarding this information. A user with concerns about the appropriate coated steel to order for a speci? Values outside of these ranges are to be expected.

We advise that you only use the original value or one of its raw conversions in your calculations to minimize rounding error. The purchaser may negotiate with the supplier if a speci? Inch-pound to SI conversions are reliable to? Some of the reasons for this limited relationship are the following: I Shall contain silicon 1.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. They are intended solely to provide the purchaser with as much information as possible to make an informed decision on the steel to be speci?


ASTM A Aluminum-Coated Steel, Type I, Drawing Quality

These factors 3 include: It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Property Data This page displays only the text of a material data sheet. C As there is no discontinuous yield curve, the yield strength should be taken as the stress at 0. If the hardness result is 85 HRB or higher, no tension test is required.

E For satm levels less than or equal to 0. Each system shall be used independently of the other. These mechanical property values are nonmandatory. C When a deoxidized steel is required for the application, the purchaser has the option to order CS and FS to a minimum of 0.

ASTM A463 Grade FSS-439

Structural steel and high strength low alloy steel shall conform to the mechanical property requirements. Historical Version s – view previous versions of standard.

Originally published as A — 62 T. The relationship between the a43 may only be approximate; therefore, the respective documents should be consulted for actual requirements. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

It adtm available as a coating on each of the designations of steel sheet listed in 4. A One ounce of Type 1 aluminum coating per square foot of surface corresponds to an average coating thickness of 0.